This Travertine Tiled kitchen floor was in a farmhouse close to the village of Newnham near Daventry. The client had called us in because she was concerned that her floor was becoming increasingly difficult to keep clean which was due to the small holes and pits becoming ingrained with soil and it was becoming difficult to remove as the original sealant had worn off.
Hopefully you can see from the pictures the results that can be achieved on a badly stained and pitted Travertine floor. The first photo below shows the extent of the problem due to many holes in the floor, this is a characteristic of Travertine and normally these holes are filled in the factory but the filler does come out over time leaving holes.
Cleaning a Pitted Travertine Tiled Floor
The floor was cleaned using a combination of Tile Doctor Burnishing Pads to re-surface the tile and the application of Tile Doctor Grout Pro-Clean agitated with a stiff brush to clean out embedded soil in the pits and grout lines. The Burnishing pads fit a rotary floor polishing machine and come in a series of different grits which are applied from Coarse through Medium and then Fine and lubricated with a little water.
I also carried out some repairs to the larger holes with a travertine filler that was mixed to match the existing colours. The second picture shows the repairs in progress, the filler is mixed and applied before leaving an hour and then polishing off any excess filler with dry cloth, the floor was then vacuumed and allowed to fully dry overnight allowing the product to harden.
Sealing a Travertine Tiled Floor
The floor was polished and sealed the following day using 2 coats of Tile Doctor Ultra Seal sealant to protect the grout lines and stone from any staining in future, it leaves a no-sheen natural look which worked very well in the kitchen area.
I waited a for the sealant to dry and then carried out a water repellency test to check it was fully sealed before giving the floor a final polish using a Tile Doctor Polishing Pad.
Details below of an unusual Travertine tiled kitchen floor in Greet, Gloucestershire where we were asked to restore the appearance of the tiles and leave a natural as opposed to shiny finish. Greet is a lovely little village at the edge of the Cotsworlds and famous for being a short walk to Winchcombe station on the Gloucestershire Warwickshire Railway which is run by volunteers and often has steam trains running on its line.
Burnishing a Travertine Tiled Floor
Travertine responds well to burnishing which is an abrasive cleaning method as opposed to chemical. Basically, it involves the application of several different grades of diamond encrusted pad to the stone lubricated with a small amount of water. You run the pad over each tile and then give the floor a quick rinse before moving on to the next pad, I started with the first of the four burnishing pads which is a coarse 400 grit pad that designed to grind away the dirt and old sealer on the surface of the floor.
After applying the first pad, I moved my way through the medium 800 and fine 1500 grit pads to gradually restore the appearance of the Travertine. Normally I would of also applied the fourth pad in the series but if you recall the customer did not wanted a polished appearance so I stopped after the 1500 grit pad.
The pads work well on tile but struggle to reach recessed grout so to clean that I applied a medium dilution of Tile Doctor Pro-Clean and scrubbed it into the grout lines manually using a stiff grout brush. Once I was happy with the appearance of the grout the soiled cleaning solution was rinsed away with water and extracted using a wet vacuum leaving the floor to dry off overnight.
Sealing a Travertine Tiled Floor
The next day I returned to finish the floor and first task was to run a Tan buffing pad over the floor to ensure the floor was clean and any residue from the diamond pad burnishing had been removed.
Once I was happy with the tiles I proceeded to apply two coats of Tile Doctor Colour Grow which is an impregnating sealer that protects from within by occupying the pores in the stone so dirt can penetrate and lifts the natural colours in the stone in the process.
I should mention that normally only one coat of Colour Grow is usually required to seal Travertine however on this occasion the stone was quite porous.
The colours in the Travertine were so much more vibrant after the job was completed and the customer was happy with the result, although personally I would have preferred to have applied the fourth pad to build up the shine however I delivered what the customer had asked for so I was happy with that.